107 802
Assignments Done
100%
Successfully Done
In November 2024
In November 2024
Your physics assignments can be a real challenge, and the due date can be really close — feel free to use our assistance and get the desired result.
Physics
Be sure that math assignments completed by our experts will be error-free and done according to your instructions specified in the submitted order form.
Math
Our experts will gladly share their knowledge and help you with programming projects. Keep up with the world’s newest programming trends.
Programming
Learn more about our help with Assignments: Engineering
Search & Filtering
Thermal Power Engineering
Many household use common hot water heating system which delivers hot water to the radiators at 60.0'c. Then, the water leaves the radiators at 28.0'c. New, heating system utilizes steam which at atm pressure condenses in the radiator. Then, the condensed steam leaves the radiators at 35.0'c. How many kg of steam must be produced the same amount of heat supplied by 1.00 kg of hot water?
Thermal Power Engineering
Comparing the efficiency of the real power plant cycle with the ideal Rankine cycle shows:
A.
the efficiency of the real power plant cycle is equal to the ideal Rankine cycle
B.
the efficiency of the real power plant cycle is higher than the Carnot cycle
C.
the efficiency of the real power plant cycle is less than the ideal Rankine cycle
D.
the efficiency of the real power plant cycle is higher than the ideal Rankine cycle
A.
the efficiency of the real power plant cycle is equal to the ideal Rankine cycle
B.
the efficiency of the real power plant cycle is higher than the Carnot cycle
C.
the efficiency of the real power plant cycle is less than the ideal Rankine cycle
D.
the efficiency of the real power plant cycle is higher than the ideal Rankine cycle
Thermal Power Engineering
gas having a volume of 0.05 m 3 and pressure of 6.9 bar expands reversibly in a cylinder behind a piston according to lawpv1. 2 = constant until the volume is 0.08 m3. Calculate the work done by the gas. Also sketch the process on a p-v diagram. [Ans.15300 Nm]
Thermal Power Engineering
Q1. A sample of partially saturated sand had a volume of 95 x 10-6 m3 and a mass of 0.2 kg. After oven drying, its mass was 0.19 kg. Calculate the bulk density, dry density, saturated density, porosity, void ratio, moisture content, degree of saturation and air void ratio of the sample. Assume Gs = 2.6.
Thermal Power Engineering
Argon is contained in a 3 m
3
rigid volume at 75 C and 400 kPa. Calculate the heat transfer
needed to increase the pressure to 800 kPa.
3
rigid volume at 75 C and 400 kPa. Calculate the heat transfer
needed to increase the pressure to 800 kPa.
Thermal Power Engineering
Air is compresses in a two-stage vane-type compressor from 1.013 bar to.
8.75 bar Using the data below, and assuming equal pressure ratios in each
stage, that compression is complete in each stage that the machine
operates in an ideal manner and is uncooled apart from the intercooler,
calculate:
(i) the power required.
(ii) The volume flow rate measured at the delivery pressure.
8.75 bar Using the data below, and assuming equal pressure ratios in each
stage, that compression is complete in each stage that the machine
operates in an ideal manner and is uncooled apart from the intercooler,
calculate:
(i) the power required.
(ii) The volume flow rate measured at the delivery pressure.
Thermal Power Engineering
A double pipe heat exchanger has an effectiveness of 0.5 when the flow is
counter- current and the thermal capacity of one fluid is twice that of the
other fluid. Calculate the effectiveness of the heat exchanger if the direction
of flow of one of the fluids is reversed with the same mass flow rates as
before?
counter- current and the thermal capacity of one fluid is twice that of the
other fluid. Calculate the effectiveness of the heat exchanger if the direction
of flow of one of the fluids is reversed with the same mass flow rates as
before?
Thermal Power Engineering
A rankine cycle has the following operating conditions, steam pressure, 2.5 MPa, steam temperature, 280°C, Exhaust pressure 0.026 MPa, indicated steam rate, 5.45 kg/kwh, mechanical efficiency, 90%. For ideal cycle and engine, calculate (a) thermal efficiency, (b) The engine steam rate, (c) The actual condition of exhaust steam, and (d) The steam flow rate in kg/h for 1 Mw generator output at 94% efficiency. Ans. (a) 28.6%, 28.5%; (b) 4.69 kg/kwh; (c) 86.33%; (d) 6447 kg/h
Thermal Power Engineering
i want to know about all dimensions of solar flat plate collector for modeling in cad software.
please help me with it. i want it for capacity of 200 L.
please help me with it. i want it for capacity of 200 L.
Thermal Power Engineering
A piston cylinder contains gas initially at 3500 kPa with a volume of 0.03 cubic meter. The gas is compressed during a process where pV raise to 4.25 = C to a pressure og 8500 kPa. The heat transfer from the gas is 2.5 kJ. Determine the change in internal energy, neglecting changes in kinetic and potential energies.
-
![Help me with my assignment!]()
Who Can Help Me with My Assignment
There are three certainties in this world: Death, Taxes and Homework Assignments. No matter where you study, and no matter…
-
![How to finish assignment]()
How to Finish Assignments When You Can’t
Crunch time is coming, deadlines need to be met, essays need to be submitted, and tests should be studied for.…
-
![Math Exams Study]()
How to Effectively Study for a Math Test
Numbers and figures are an essential part of our world, necessary for almost everything we do every day. As important…
"assignmentexpert.com" is professional group of people in Math subjects! They did assignments in very high level of mathematical modelling in the best quality. Thanks a lot
#339914 on Dec 2023
#339914 on Dec 2023